GSW's range of Kolinsky brushes, SILVER SERIES. Expertly hand-crafted with a high quality wooden handle and a tip of  natural Kolinsky hair, fused together by a brass ferrule. For amateur and experts alike, the SILVER SERIES range of Kolinsky brushes will provide a smooth and crisp painting experience.

They work best with water-based acrylic paints, especially with fine techniques such as washing, blending, layering and degrading. In general, they are recommended for any technique which requires a more diluted medium. We advise against single stroke or dry brushing techniques as these may harm the tip.

This type of hair ensures a high absorption of water and paint and excellent elasticity, making it a very technical brush.

By nature, natural brushes require more care than synthetic hair brushes, as their decay may lead to a loss of firmness and broken hairs. In order for your kolinsky brushes to last longer we recommend avoiding leaving any paint residue to dry in the bristles and shaping them and sharpening the point with our Brush Repair Gel (LINK). After painting, let them stand with the bristles pointing upwards to avoid deforming the tips.

We do not recommended using Kolinsky brushes for oil paint, since the products required to clean the bristles after this type of paint can deteriorate the Kolinsky natural hair quickly.

Good maintenance of these brushes will ensure their longevity.

This set contains:

1x Kolinsky Brush - Size 00
1x Kolinsky Brush - Size 0
1x Kolinsky Brush - Size 1
1x Kolinsky Brush - Size 2

Milliput is a epoxy putty used by modellers for all kind of applications. Each package contains two separate bars, one of which is a hardener. Upon mixing an equal quantity of each different bar the material starts to harden, and hardens fully in 90 minutes, after which it can be carved, sanded, drilled, and sculpted over.

If you are interrupted while you are mixing Milliput, you can put the Milliput into a deep freezer until you can get back to work. This will keep the product at approximately the same state of setting at which it was frozen for up to 24 hours

OTHER ADVANTANGES:

-        In combination with water will allow to get extra smooth surfaces.

-        It allows you easily to merge new layers of milliput over

-        It will not get stuck to your either your fingers or your tools

-        Once dried, it can be carved, sanded and drilled

-        Once dried, it remains very hard and resistance. You may mix it with Plasticine or other clays to save putty reducing it hardness.

-        Heat resistance up to 130ºC.

Leaf Litter - Autumn Orange

Leaf scatter material from a natural product that is almost perfect shaped like miniature leaves and ideal for 25mm (1/76) to 45mm (1/22) figures, scenery and terrain.

Type: real miniature leaves

Leaf Sizes: 2-5mm

Net Weight: around 10gr * Enough content for 2-3 armies

Neodymium Magnets

Diameter: 3mm (1/8)
Thickness: 1mm (1/32')
Quantity: 100

Magnetisation: N52
Pull Forces: 126gr (magnet to magnet) **
Material: NdFeB
Coating: Nickel Plated (Ni-Cu-Ni)

Neodymium Magnet is the strongest type of permanent magnet commercially available. They have replaced other types of magnet in the many applications in modern products that require strong permanent magnets.

The references N35 and N52 are a measurement for the quality of the magnet material. The higher the grade (the number following the 'N'), the stronger the magnet. These will explain two things:
- How much "magnetic energy" per volume is contained in this magnet material
- Up to what temperature the magnet can be used

Magnets that begin with an "N" should be used up to 80°C (176°F).
The highest grade of neodymium magnet currently available is N52. 

If you take any two magnets of different sizes and magnetisation from our range, the difference in their strength is more due to the differences in their volume than the differences in their magnetisation. That's why the larger magnet is mostly the stronger magnet, even when its magnetisation classification is somewhat smaller.

** Pull Forces: Expected pull forces based on extensive product testing. The Surface Field data is only valid for points along the center axis of the magnet, and assumes a single magnet in free space.

If you are planning to use them with wargames and miniatures we will recommend you as follows: 

- Neodymium Magnet - 3x0.5mm, for exchanging weapons, heads, arms, etc ... 
- Neodymium Magnet - 3x1mm, for exchanging weapons, heads, arms, etc ... 
- Neodymium Magnet - 3x2mm, for plastic miniatures bases.
- Neodymium Magnet - 5x2mm, for metal miniatures bases.

Top quality plastic bases for mounting wargames figures.

Shape: Round
Thickness: 3mm
Color: Black
Bases: 20 per pack

Neodymium Magnets

Diameter: 3mm (1/8')
Thickness: 2mm (1/12')
Quantity: 100

Magnetisation: N35
Pull Forces: 190gr (magnet to magnet) **
Material: NdFeB
Coating: Nickel Plated (Ni-Cu-Ni)

Neodymium Magnet is the strongest type of permanent magnet commercially available. They have replaced other types of magnet in the many applications in modern products that require strong permanent magnets.

The references N35 and N52 are a measurement for the quality of the magnet material. The higher the grade (the number following the 'N'), the stronger the magnet. These will explain two things:
- How much "magnetic energy" per volume is contained in this magnet material
- Up to what temperature the magnet can be used

Magnets that begin with an "N" should be used up to 80°C (176°F).
The highest grade of neodymium magnet currently available is N52. 

If you take any two magnets of different sizes and magnetisation from our range, the difference in their strength is more due to the differences in their volume than the differences in their magnetisation. That's why the larger magnet is mostly the stronger magnet, even when its magnetisation classification is somewhat smaller.

** Pull Forces: Expected pull forces based on extensive product testing. The Surface Field data is only valid for points along the center axis of the magnet, and assumes a single magnet in free space.

If you are planning to use them with wargames and miniatures we will recommend you as follows: 

- Neodymium Magnet - 3x0.5mm, for exchanging weapons, heads, arms, etc ... 
- Neodymium Magnet - 3x1mm, for exchanging weapons, heads, arms, etc ... 
- Neodymium Magnet - 3x2mm, for plastic miniatures bases.
- Neodymium Magnet - 5x2mm, for metal miniatures bases.

Diameter: 5mm (3/16')
Thickness: 2mm (1/12')
Quantity: 100

Magnetisation: N52
Pull Forces: 575gr (magnet to magnet) **
Material: NdFeB
Coating: Nickel Plated (Ni-Cu-Ni)

Neodymium Magnet is the strongest type of permanent magnet commercially available. They have replaced other types of magnet in the many applications in modern products that require strong permanent magnets.

The references N35 and N52 are a measurement for the quality of the magnet material. The higher the grade (the number following the 'N'), the stronger the magnet. These will explain two things:
- How much "magnetic energy" per volume is contained in this magnet material
- Up to what temperature the magnet can be used

Magnets that begin with an "N" should be used up to 80°C (176°F).
The highest grade of neodymium magnet currently available is N52. 

If you take any two magnets of different sizes and magnetisation from our range, the difference in their strength is more due to the differences in their volume than the differences in their magnetisation. That's why the larger magnet is mostly the stronger magnet, even when its magnetisation classification is somewhat smaller.

** Pull Forces: Expected pull forces based on extensive product testing. The Surface Field data is only valid for points along the center axis of the magnet, and assumes a single magnet in free space.

If you are planning to use them with wargames and miniatures we will recommend you as follows: 

- Neodymium Magnet - 3x0.5mm, for exchanging weapons, heads, arms, etc ... 
- Neodymium Magnet - 3x1mm, for exchanging weapons, heads, arms, etc ... 
- Neodymium Magnet - 3x2mm, for plastic miniatures bases.
- Neodymium Magnet - 5x2mm, for metal miniatures bases.

MDF BASES - ROUND 25mm

Top quality MDF bases for mounting wargames figures.

GSW Paint Remover, capable of removing acrylic, enamel and lacquer-based paints. Completely safe for miniatures in plastic, resin or metal. Can be reused several times and has low evaporation.

Partially submerge miniature in the paint stripper / paint killer for 1 to 6 hours depending on the paint type, rinse with water and remove excess with a synthetic brush. If insufficient, repeat process.

Content: 240 ml

These opaque fluorescent acrylic paints will make your miniatures and dioramas vividly colourful. They are characterised by their highly intense brightness, reaching maximum brightness over white paint.

In addition, they react and glow under ultraviolet/black light, offering an infinite number of creative possibilites.

Non-toxic. Valid for brush and airbrush.

Content: 1x 17ml bottle

Available in various colors.

*This Paint may contain a protective seal, remove before use.

Leaf Litter - Spring Green

Leaf scatter material from a natural product that is almost perfect shaped like miniature leaves and ideal for 25mm (1/76) to 45mm (1/22) figures, scenery and terrain.

Type: real miniature leaves

Leaf Sizes: 2-5mm

Net Weight: around 10gr * Enough content for 2-3 armies

Top quality plastic bases for mounting wargames figures.

Shape: Round
Thickness: 3mm
Color: Black
Bases: 10 per pack

Ceramic bricks. Scale 1:35 (1:32-1:43)

Accessory kit for modellers that need superior level of detailed presentation. High quality bricks for precise building or loose scattering.
May be painted subsequently with any colour and colour powders. Easy to cut, saw, drill and sanding.

Size of the bricks: 7,2x3,6x1,8mm

Color: Grey

Content: 500 bricks