Textured Rolling Pins capable of pressing a continuous repeated pattern on clay and putties. Made of clear PMMA plastic with amazing non-stick properties. Non-toxic. They come in several different textures that you can purchase based on your specific needs.

Length: 14'50 cm (5’5 inches)
Diameter: 2’5cm (1 inch)

USE INSTRUCTIONS: 

1st - Properly mix the putty/clay until ready according to the manufacturer's recommendations.

2nd - Extend the putty/clay on a surface to be textured. For optimal results, make sure you have got a smooth and even surface before impressing with the Rolling Pins. *** We recommend using a plain Rolling Pin for this.

3rd - Depending on the type of putty/clay, it is advisable to wet the Rolling Pin to prevent any sticking.

4th - Slowly move the Rolling Pin applying equal pressure at all points for an even texture.

5th - Trim any excess putty/clay with a sharp knife. It is recommended to do this once it has dried to avoid any deformations in the putty/clay.

MATERIALS:

There are plenty of different putties and clays on the market and all of them can be textured using the proper technique.

Usually polymer clay (Fimo or Sculpey type) are quite simple to work with these Rolling Pins as they allow for an easy correction of mistakes before they are baked. If the aim is to make textured bases, we recommend using MDF bases, because you can texture the polymer clay directly onto an MDF base, and then put it all in the oven, including the base. The cooking time of these clays are around 15 minutes at 150ºC. MDF Wood may leave a slight scent similar to that of toasted bread, but don't worry it won’t burn!

In the case of epoxy putties, there are a variety of techniques which achieve similar results. Good thing is. you do not need to bake them, so they may be applied directly onto plastic bases.

For Green Stuff putty, which is particularly sticky, it is required to slightly wet either the putty or the Rolling Pin with some water before texturing. You may also reduce the stickiness by applying talcum powder, or using Sculptor Vaseline (LINK).

Other epoxy putties like the Milliput putty, for example, are also suitable, but we wouldn't recommend to wet them much since it will hinder your work. Furthermore, if the mixture is too sticky, it is better to continue kneading until the stickiness is gone.

*** For this type of epoxy putties, it is very important to clean the rolling pins properly after use.

CARE INSTRUCTIONS:

After working with the Rolling Pins, use a Scratch Brush (LINK) and plenty of water to clean off any residue on the Rolling Pins if required.

SAFETY:

To ensure safety, children should be closely monitored by a responsible adult. 

Textured Rolling Pins capable of pressing a continuous repeated pattern on clay and putties. Made of clear PMMA plastic with amazing non-stick properties. Non-toxic. They come in several different textures that you can purchase based on your specific needs.

Length: 14'50 cm (5’5 inches)
Diameter: 2’5cm (1 inch)

USE INSTRUCTIONS: 

1st - Properly mix the putty/clay until ready according to the manufacturer's recommendations.

2nd - Extend the putty/clay on a surface to be textured. For optimal results, make sure you have got a smooth and even surface before impressing with the Rolling Pins. *** We recommend using a plain Rolling Pin for this.

3rd - Depending on the type of putty/clay, it is advisable to wet the Rolling Pin to prevent any sticking.

4th - Slowly move the Rolling Pin applying equal pressure at all points for an even texture.

5th - Trim any excess putty/clay with a sharp knife. It is recommended to do this once it has dried to avoid any deformations in the putty/clay.

MATERIALS:

There are plenty of different putties and clays on the market and all of them can be textured using the proper technique.

Usually polymer clay (Fimo or Sculpey type) are quite simple to work with these Rolling Pins as they allow for an easy correction of mistakes before they are baked. If the aim is to make textured bases, we recommend using MDF bases, because you can texture the polymer clay directly onto an MDF base, and then put it all in the oven, including the base. The cooking time of these clays are around 15 minutes at 150ºC. MDF Wood may leave a slight scent similar to that of toasted bread, but don't worry it won’t burn!

In the case of epoxy putties, there are a variety of techniques which achieve similar results. Good thing is. you do not need to bake them, so they may be applied directly onto plastic bases.

For Green Stuff putty, which is particularly sticky, it is required to slightly wet either the putty or the Rolling Pin with some water before texturing. You may also reduce the stickiness by applying talcum powder, or using Sculptor Vaseline (LINK).

Other epoxy putties like the Milliput putty, for example, are also suitable, but we wouldn't recommend to wet them much since it will hinder your work. Furthermore, if the mixture is too sticky, it is better to continue kneading until the stickiness is gone.

*** For this type of epoxy putties, it is very important to clean the rolling pins properly after use.

CARE INSTRUCTIONS:

After working with the Rolling Pins, use a Scratch Brush (LINK) and plenty of water to clean off any residue on the Rolling Pins if required.

SAFETY:

To ensure safety, children should be closely monitored by a responsible adult. 

Textured Rolling Pins capable of pressing a continuous repeated pattern on clay and putties. Made of clear PMMA plastic with amazing non-stick properties. Non-toxic. They come in several different textures that you can purchase based on your specific needs.

Length: 14'50 cm (5’5 inches)
Diameter: 2’5cm (1 inch)

USE INSTRUCTIONS: 

1st - Properly mix the putty/clay until ready according to the manufacturer's recommendations.

2nd - Extend the putty/clay on a surface to be textured. For optimal results, make sure you have got a smooth and even surface before impressing with the Rolling Pins. *** We recommend using a plain Rolling Pin for this.

3rd - Depending on the type of putty/clay, it is advisable to wet the Rolling Pin to prevent any sticking.

4th - Slowly move the Rolling Pin applying equal pressure at all points for an even texture.

5th - Trim any excess putty/clay with a sharp knife. It is recommended to do this once it has dried to avoid any deformations in the putty/clay.

MATERIALS:

There are plenty of different putties and clays on the market and all of them can be textured using the proper technique.

Usually polymer clay (Fimo or Sculpey type) are quite simple to work with these Rolling Pins as they allow for an easy correction of mistakes before they are baked. If the aim is to make textured bases, we recommend using MDF bases, because you can texture the polymer clay directly onto an MDF base, and then put it all in the oven, including the base. The cooking time of these clays are around 15 minutes at 150ºC. MDF Wood may leave a slight scent similar to that of toasted bread, but don't worry it won’t burn!

In the case of epoxy putties, there are a variety of techniques which achieve similar results. Good thing is. you do not need to bake them, so they may be applied directly onto plastic bases.

For Green Stuff putty, which is particularly sticky, it is required to slightly wet either the putty or the Rolling Pin with some water before texturing. You may also reduce the stickiness by applying talcum powder, or using Sculptor Vaseline (LINK).

Other epoxy putties like the Milliput putty, for example, are also suitable, but we wouldn't recommend to wet them much since it will hinder your work. Furthermore, if the mixture is too sticky, it is better to continue kneading until the stickiness is gone.

*** For this type of epoxy putties, it is very important to clean the rolling pins properly after use.

CARE INSTRUCTIONS:

After working with the Rolling Pins, use a Scratch Brush (LINK) and plenty of water to clean off any residue on the Rolling Pins if required.

SAFETY:

To ensure safety, children should be closely monitored by a responsible adult. 

Textured Rolling Pins capable of pressing a continuous repeated pattern on clay and putties. Made of clear PMMA plastic with amazing non-stick properties. Non-toxic. They come in several different textures that you can purchase based on your specific needs.

Length: 14'50 cm (5’5 inches)
Diameter: 2’5cm (1 inch)

USE INSTRUCTIONS: 

1st - Properly mix the putty/clay until ready according to the manufacturer's recommendations.

2nd - Extend the putty/clay on a surface to be textured. For optimal results, make sure you have got a smooth and even surface before impressing with the Rolling Pins. *** We recommend using a plain Rolling Pin for this.

3rd - Depending on the type of putty/clay, it is advisable to wet the Rolling Pin to prevent any sticking.

4th - Slowly move the Rolling Pin applying equal pressure at all points for an even texture.

5th - Trim any excess putty/clay with a sharp knife. It is recommended to do this once it has dried to avoid any deformations in the putty/clay.

MATERIALS:

There are plenty of different putties and clays on the market and all of them can be textured using the proper technique.

Usually polymer clay (Fimo or Sculpey type) are quite simple to work with these Rolling Pins as they allow for an easy correction of mistakes before they are baked. If the aim is to make textured bases, we recommend using MDF bases, because you can texture the polymer clay directly onto an MDF base, and then put it all in the oven, including the base. The cooking time of these clays are around 15 minutes at 150ºC. MDF Wood may leave a slight scent similar to that of toasted bread, but don't worry it won’t burn!

In the case of epoxy putties, there are a variety of techniques which achieve similar results. Good thing is. you do not need to bake them, so they may be applied directly onto plastic bases.

For Green Stuff putty, which is particularly sticky, it is required to slightly wet either the putty or the Rolling Pin with some water before texturing. You may also reduce the stickiness by applying talcum powder, or using Sculptor Vaseline (LINK).

Other epoxy putties like the Milliput putty, for example, are also suitable, but we wouldn't recommend to wet them much since it will hinder your work. Furthermore, if the mixture is too sticky, it is better to continue kneading until the stickiness is gone.

*** For this type of epoxy putties, it is very important to clean the rolling pins properly after use.

CARE INSTRUCTIONS:

After working with the Rolling Pins, use a Scratch Brush (LINK) and plenty of water to clean off any residue on the Rolling Pins if required.

SAFETY:

To ensure safety, children should be closely monitored by a responsible adult. 

Green Stuff World's basic mission objective markers are transparent circles only 1 mm thick, featuring printed edges that precisely mark the mission zones on Warhammer 40k® and WTC-compatible tables. Each pack includes six markers: a 40 mm inner disc (base size) surrounded by a 3" scoring ring, all made from flexible, shatterproof glasspack plastic.

Thanks to their full transparency, they don’t break the immersion of your wargaming mat or create bumps that cause miniatures to wobble. The printed edge clearly shows where the control zone starts and ends, helping avoid arguments and speeding up OC (Objective Controlled) counting. The laser-etched edges work great on grey or dark mats, but they’re not ideal for very light-colored surfaces like snowy terrain, as the edges might blend with the background. Lightweight and stackable, they fit easily into any tournament miniatures case.

At deployment, drop the six discs where the mission map tells you; touch the 40 mm core to score, and the outer ring shows at a glance who’s within 3″. WTC events require markers to stay put even if terrain shifts, so the 1 mm profile and full transparency are perfect—no snagging scenery, no blocking movement.

Content: x6

MDF movement trays are very popular among wargame and miniatures game enthusiasts as they provide stability in the displacement of troops, and customization by unifying the formations of the units of your armies, in addition to their great compatibility with a multitude of game systems. They serve as a solid base for assembling, transporting, and displaying your wargame figures, enhancing both the gaming experience and the visual aesthetics of the battlefield. They help maintain a level playing field and accurately measure distances and unit displacements.

This set is made of MDF wood and laser-cut with high precision. The base grid has been engraved to facilitate the placement of the figures and also has no edge, so the minis are completely glued to the edge of the movement bases so that, no space is created when joining two units facing each other.

Top quality MDF bases for mounting wargames figures.

A 3D-printed set designed for modeling and wargames can be an excellent addition to your hobby toolkit. They offer the opportunity to create custom and intricately detailed terrain pieces, DnD miniatures, and Warhammer Skaven accessories, elevating your gaming experience. Adding these high-quality ABS-like resin bitz to your bases, dioramas, and figures can bring a realistic touch to your creations. Carefully crafted to mimic real species, these bits come in various shapes and sizes, catering to a wide range of needs and scales. Whether you're a model enthusiast or a tabletop gamer, these 3D-printed bits provide versatility and creativity to enhance your hobby projects.

Choosing the appropriate modeling glue, modeling tools, or approach for a given task with your Warhammer bits is essential for achieving optimal results and efficiency in any project. Understanding the project's requirements, researching available options, and evaluating their performance and suitability are key factors. Additionally, considering the expertise and resources available, staying up-to-date with the latest developments, seeking advice from experts, and thinking about long-term maintenance are all crucial aspects of making an informed decision.

This product comes unpainted and is perfect for 25-28-35-54 mm (1:48 - 1:35) miniatures.

Each set contains 14 x resin Vampire Bats

Extra Cabinet

Extra Cabinet is designed to complement the transport and storage of miniatures. It can be used both as an additional cabinet for the GSW Army Transport Bag and as a free-standing stackable storage system.

Manufactured of MDF wood is capable of accommodating more than 200 miniatures distributed among its rack levels.

It includes 4 removable metalized trays and its height is adjustable up to 11 levels to place the trays with your miniatures.

If you want to gain a few extra centimeters of inner space, you could remove the first lower MDF tray, and glue the metallized rubber directly to the base of the case. To make this modification, simply cut with scissors the rubber so that it can fit. By doing so, the lower level will no longer be removable.

Size: 7x11,8x11,8 in. (18x30x30cm). Total weights 2,3kg. Assembly instructions inside.

Includes:

- 1x Complete cabinet

- 4x Trays + 4x adhesive metallized rubber sheets

3D printed set

Set of high quality resin plants. Carefully designed to imitate real species and come in different shapes and sizes to suit all needs and scales. Ideal for dioramas and scenery.

This product comes unpainted and is perfect for 1:48.

Contains: x25

Hobby Sand

Sand used for bases and modeling made out of the gravel. It is recommended to apply with either white glue or cyanoacrylate glue.

Size of grain: Approx. 1-3mm
Colour: Natural
Contains: 200ml

Acrylic texture for rust effects, developed to enhance and give volume texture and details to the scale models, creating extremely rusted surfaces. Texturizes and colors the surface, apply in layers of the desired thickness. It can be diluted with water or an acrylic thinner to modify its fluidity.

This textured paste is thick and has a dense consistency, suitable for representing rust textures on diorama or vignette bases. It can be easily spread with a brush or spatula. Dries in 5-30 minutes depending on the thickness of the application. Water-soluble. Tools can be cleaned with water.

Contains 1 bottle of 30ml textured paste

Decorate your bases, dioramas and terrain pieces with these amazing resin crystals to make them look unique, personalised and stand out.

This set includes medium crystals of various types and sizes. The crystals can be single or multiple, with some pieces carrying up to 4 crystals. The approximate size of the pieces are from 9mm to 16mm tall.

Made of premium quality resin.

Contains 50x crystals.

Transparent acrylic filters with a metallic finish that allow to modify and metalize the colour they cover. Apply on top of other flat, metallic, or colourshift colours. Mixed together, or applied successively, they create new combinations. Shiny metallic finish. Valid for brush or airbrush.

They work similarly to Chameleon Colourshifts, but they are just one colour and the chameleonic effect is achieved through the combination of the base colour and the metal filter. You can apply them to any flat colour to essentially turn it into a Chameleon Colourshift of your own design.

It is preferable to apply over dark colours to appreciate their effect better, though over black you'll only see the tone of the metal filter. Over other dark colours you can create many combinations, we encourage you to experiment as the possibilities with these are endless!

Contents

1x 17ml Turquoise Interference

Transparent acrylic filters with a metallic finish that allow to modify and metalize the color they cover. Apply on top of other flat, metallic, or colorshift colours. Mixed together, or applied successively, they create new combinations. Shiny metallic finish. Valid for brush or airbrush.

They work similarly to our Chameleon Colorshifts, but they are just one colour and the chamaleonic effect is achieved through the combination of the base colour and the metal filter. You can apply them to any flat colour to essentially turn it into a Chameleon Colorshift of your own design.

It is preferable to apply over dark colours to appreciate their effect better, though over black you'll only see the tone of the metal filter. Over other dark colours you can create many combinations, we encourage you to experiment as the possibilities with these are endless!

Content:

1x Blue Interference
1x Purple Interference
1x Turquoise Interference
1x Green Interference
1x Gold Interference
1x Red Interference

Scale cutting mat is perfect for modeling, measuring, sculpting and general craft cutting and protecting surfaces from craft paints. This pack contains one high density double-sided cutting matt that will help cut the perfect angle and size every time. Due to the high density material, the matt will prevent blades from slipping, which will give you a better cut and will decrease the likeliness of injury.

On one side of the Mat are printed the guide lines of the most common scales, which will allow you to create armatures for sculpting miniatures of people. On the other side you will finde the same scales and guide lines to create horses and warhorses armatures

Dimensions: 200mm x 300mm
Thickness: 3mm
Color: Black
Self Healing High Density PVC Material
Non slip doubleside matt

Acrylic paints with an opaque and smooth matt finish, especially designed for modelling and miniature painting. Formula curated and carefully developed by experienced artists using a new generation of pigments, the Acrylic Color range aims to provide a full spectrum of all basic tones and shades necessary for wargames, vehicles, miniatures and dioramas, as well as colours exclusive to GSW.

Rich in high quality pigments, these colours will leave a fine homogenous layer of fast drying paint, respecting all details on the surface. Perfect for glazes and other techniques, making them adequate for experts and amateurs alike. Designed especially for brush painting, but Acrylic Color paints can be used with an airbrush when slightly diluted with Acrylic Thinner.

Non-toxic water-based with no latex. Shake well before use. Includes stainless steel mixing ball.

Contains: 17ml.

*This Paint may contain a protective seal, remove before use.

Acrylic paints with an opaque and smooth matt finish, especially designed for modelling and miniature painting. Formula curated and carefully developed by experienced artists using a new generation of pigments, the Acrylic Color range aims to provide a full spectrum of all basic tones and shades necessary for wargames, vehicles, miniatures and dioramas, as well as colours exclusive to GSW.

Rich in high quality pigments, these colours will leave a fine homogenous layer of fast drying paint, respecting all details on the surface. Perfect for glazes and other techniques, making them adequate for experts and amateurs alike. Designed especially for brush painting, but Acrylic Color paints can be used with an airbrush when slightly diluted with Acrylic Thinner.

Non-toxic water-based with no latex. Shake well before use. Includes stainless steel mixing ball.

Contains: 17ml.

*This Paint may contain a protective seal, remove before use.

Textured Rolling Pins capable of pressing a continuous repeated pattern on clay and putties. Made of clear PMMA plastic with amazing non-stick properties. Non-toxic. They come in several different textures that you can purchase based on your specific needs.

Length: 14'50 cm (5’5 inches)
Diameter: 2’5cm (1 inch)
Pattern Size: 1-4 mm (variable with multiple stone types, all of them different)
Recommended Scales: 1/144 - 1/100 - 1/72 (12-15-20mm miniatures)

USE INSTRUCTIONS:

1st - Properly mix the putty/clay until ready according to the manufacturer's recommendations.

2nd - Extend the putty/clay on a surface to be textured. For optimal results, make sure you have got a smooth and even surface before impressing with the Rolling Pins. *** We recommend using a plain Rolling Pin for this.

3rd - Depending on the type of putty/clay, it is advisable to wet the Rolling Pin to prevent any sticking.

4th - Slowly move the Rolling Pin applying equal pressure at all points for an even texture.

5th - Trim any excess putty/clay with a sharp knife. It is recommended to do this once it has dried to avoid any deformations in the putty/clay.

MATERIALS:

There are plenty of different putties and clays on the market and all of them can be textured using the proper technique.

Usually polymer clay (Fimo or Sculpey type) are quite simple to work with these Rolling Pins as they allow for an easy correction of mistakes before they are baked. If the aim is to make textured bases, we recommend using MDF bases, because you can texture the polymer clay directly onto an MDF base, and then put it all in the oven, including the base. The cooking time of these clays are around 15 minutes at 150ºC. MDF Wood may leave a slight scent similar to that of toasted bread, but don't worry it won’t burn!

In the case of epoxy putties, there are a variety of techniques which achieve similar results. Good thing is. you do not need to bake them, so they may be applied directly onto plastic bases.

For Green Stuff putty, which is particularly sticky, it is required to slightly wet either the putty or the Rolling Pin with some water before texturing. You may also reduce the stickiness by applying talcum powder, or using Sculptor Vaseline (LINK).

Other epoxy putties like the Milliput putty, for example, are also suitable, but we wouldn't recommend to wet them much since it will hinder your work. Furthermore, if the mixture is too sticky, it is better to continue kneading until the stickiness is gone.

*** For this type of epoxy putties, it is very important to clean the rolling pins properly after use.

CARE INSTRUCTIONS:

After working with the Rolling Pins, use a Scratch Brush and plenty of water to clean off any residue on the Rolling Pins if required.

SAFETY:

To ensure safety, children should be closely monitored by a responsible adult.

Textured Rolling Pins capable of pressing a continuous repeated pattern on clay and putties. Made of clear PMMA plastic with amazing non-stick properties. Non-toxic. They come in several different textures that you can purchase based on your specific needs.

Length: 14'50 cm (5’5 inches)
Diameter: 2’5cm (1 inch)
Pattern Size: 1-4 mm (variable with multiple stone types, all of them different)
Recommended Scales: 1/144 - 1/100 - 1/72 (12-15-20mm miniatures)

USE INSTRUCTIONS:

1st - Properly mix the putty/clay until ready according to the manufacturer's recommendations.

2nd - Extend the putty/clay on a surface to be textured. For optimal results, make sure you have got a smooth and even surface before impressing with the Rolling Pins. *** We recommend using a plain Rolling Pin for this.

3rd - Depending on the type of putty/clay, it is advisable to wet the Rolling Pin to prevent any sticking.

4th - Slowly move the Rolling Pin applying equal pressure at all points for an even texture.

5th - Trim any excess putty/clay with a sharp knife. It is recommended to do this once it has dried to avoid any deformations in the putty/clay.

MATERIALS:

There are plenty of different putties and clays on the market and all of them can be textured using the proper technique.

Usually polymer clay (Fimo or Sculpey type) are quite simple to work with these Rolling Pins as they allow for an easy correction of mistakes before they are baked. If the aim is to make textured bases, we recommend using MDF bases, because you can texture the polymer clay directly onto an MDF base, and then put it all in the oven, including the base. The cooking time of these clays are around 15 minutes at 150ºC. MDF Wood may leave a slight scent similar to that of toasted bread, but don't worry it won’t burn!

In the case of epoxy putties, there are a variety of techniques which achieve similar results. Good thing is. you do not need to bake them, so they may be applied directly onto plastic bases.

For Green Stuff putty, which is particularly sticky, it is required to slightly wet either the putty or the Rolling Pin with some water before texturing. You may also reduce the stickiness by applying talcum powder, or using Sculptor Vaseline (LINK).

Other epoxy putties like the Milliput putty, for example, are also suitable, but we wouldn't recommend to wet them much since it will hinder your work. Furthermore, if the mixture is too sticky, it is better to continue kneading until the stickiness is gone.

*** For this type of epoxy putties, it is very important to clean the rolling pins properly after use.

CARE INSTRUCTIONS:

After working with the Rolling Pins, use a Scratch Brush and plenty of water to clean off any residue on the Rolling Pins if required.

SAFETY:

To ensure safety, children should be closely monitored by a responsible adult.

GSW's range of Candy Inks. Their excellent brightness and transparency allow them to be used for colour filters for modifying metals, gems, glass, lights, visors... or any other parts which you would want to intensify their colours. Dries fast for a gloss and smooth finish.

Can be applied by brush and airbrush.
- Applying by brush will yield a lacquered and intense finish. It must be left to dry completely and big cumulations of paint should be avoided, as this will affect their properties.
- If using an airbrush, the colour filters will be thinner and can be used to modify the chameleon colours, as well as for other metallic or transparent effects.

Contains: 17 ml

Tree Bush - Clump Foliage - DARK GREEN

A specially produced ground foam for bushes, undergrowth and clump foliage. Models medium-to-large ground cover. It is great for landscaping hillsides.

Content: 180 ml (L) - This format contains an average of 50-80 ml extra over most other brands