Textured Rolling Pins capable of pressing a continuous repeated pattern on clay and putties. Made of clear PMMA plastic with amazing non-stick properties. Non-toxic. They come in several different textures that you can purchase based on your specific needs.

Length: 14'50 cm (5’5 inches)
Diameter: 2’5cm (1 inch)

USE INSTRUCTIONS: 

1st - Properly mix the putty/clay until ready according to the manufacturer's recommendations.

2nd - Extend the putty/clay on a surface to be textured. For optimal results, make sure you have got a smooth and even surface before impressing with the Rolling Pins. *** We recommend using a plain Rolling Pin for this.

3rd - Depending on the type of putty/clay, it is advisable to wet the Rolling Pin to prevent any sticking.

4th - Slowly move the Rolling Pin applying equal pressure at all points for an even texture.

5th - Trim any excess putty/clay with a sharp knife. It is recommended to do this once it has dried to avoid any deformations in the putty/clay.

MATERIALS:

There are plenty of different putties and clays on the market and all of them can be textured using the proper technique.

Usually polymer clay (Fimo or Sculpey type) are quite simple to work with these Rolling Pins as they allow for an easy correction of mistakes before they are baked. If the aim is to make textured bases, we recommend using MDF bases, because you can texture the polymer clay directly onto an MDF base, and then put it all in the oven, including the base. The cooking time of these clays are around 15 minutes at 150ºC. MDF Wood may leave a slight scent similar to that of toasted bread, but don't worry it won’t burn!

In the case of epoxy putties, there are a variety of techniques which achieve similar results. Good thing is. you do not need to bake them, so they may be applied directly onto plastic bases.

For Green Stuff putty, which is particularly sticky, it is required to slightly wet either the putty or the Rolling Pin with some water before texturing. You may also reduce the stickiness by applying talcum powder, or using Sculptor Vaseline (LINK).

Other epoxy putties like the Milliput putty, for example, are also suitable, but we wouldn't recommend to wet them much since it will hinder your work. Furthermore, if the mixture is too sticky, it is better to continue kneading until the stickiness is gone.

*** For this type of epoxy putties, it is very important to clean the rolling pins properly after use.

CARE INSTRUCTIONS:

After working with the Rolling Pins, use a Scratch Brush (LINK) and plenty of water to clean off any residue on the Rolling Pins if required.

SAFETY:

To ensure safety, children should be closely monitored by a responsible adult. 

Acrylic paints with an opaque and smooth matt finish, especially designed for modelling and miniature painting. Formula curated and carefully developed by experienced artists using a new generation of pigments, the Acrylic Color range aims to provide a full spectrum of all basic tones and shades necessary for wargames, vehicles, miniatures and dioramas, as well as colours exclusive to GSW.

Rich in high quality pigments, these colours will leave a fine homogenous layer of fast drying paint, respecting all details on the surface. Perfect for glazes and other techniques, making them adequate for experts and amateurs alike. Designed especially for brush painting, but Acrylic Color paints can be used with an airbrush when slightly diluted with Acrylic Thinner.

Non-toxic water-based with no latex. Shake well before use. Includes stainless steel mixing ball.

Contains: 17ml.

*This Paint may contain a protective seal, remove before use.

Acrylic paints with an opaque and smooth matt finish, especially designed for modelling and miniature painting. Formula curated and carefully developed by experienced artists using a new generation of pigments, the Acrylic Color range aims to provide a full spectrum of all basic tones and shades necessary for wargames, vehicles, miniatures and dioramas, as well as colours exclusive to GSW.

Rich in high quality pigments, these colours will leave a fine homogenous layer of fast drying paint, respecting all details on the surface. Perfect for glazes and other techniques, making them adequate for experts and amateurs alike. Designed especially for brush painting, but Acrylic Color paints can be used with an airbrush when slightly diluted with Acrylic Thinner.

Non-toxic water-based with no latex. Shake well before use. Includes stainless steel mixing ball.

Contains: 17ml.

*This Paint may contain a protective seal, remove before use.

GSW's high quality resin replications of metal oil barrels. Designed to fit most standard wargames such as Infinity, Warhammer 40K and Bolt Action, these barrels will provide additional coverage and detail to your battles.

The barrels come in multiple types; decayed barrels with dents and signs of corrosion and new barrels. Furthermore, out of the set of 8 barrels, 2 are hollow and open, allowing you to bend them with pliers for them to look more damaged.

Size: 14mm diameter x 20mm height

Innovative self-adhesive scenic basing tufts perfect for decorating miniature bases, scenery, field paths, lake, river shores, embankments & slopes as well as the edges of forests and roads, creating flower beds or to brighten meadows. Just take the grass tufts out of the package using tweezers and fix them with its self-adhesive sticky bases. Although self adhesive, a dab of glue may be required to apply to some surfaces for a permanent fix.

Type of Flock: NYLON FLOCK
Fiber Size: 2mm high
Plastic sheet size: 4x15cm
Content: 40-50 tufts

A vast treasure of 16 pieces of differing sizes. From small mounds of coins to medium and larger mounds of coins containing goblets, jewellery, treasure chests and sacks of money to add some extravagant wealth to your miniatures and dioramas.

This product comes unpainted and it is perfect for 32-54 mm miniatures (1:48, 1:35).

This set contains 16x Resin Treasure Pieces.

The perfect combination of paints to create the impression of silver or steel metal on your miniatures, without using metallic paint. Non-metallic metal set of acrylic paints with an opaque and smooth matt finish, especially designed for modelling and miniature painting. Curated and carefully developed by experienced artists using a new generation of pigments, the Acrylic Color range aims to provide a full spectrum of all basic tones and shades necessary for wargames, vehicles, miniatures and dioramas, as well as colours exclusive to GSW.

Rich in high quality pigments, these colours will leave a fine homogenous layer of fast drying paint, respecting all details on the surface. Perfect for glazes and other techniques, making them adequate for experts and amateurs alike. Designed especially for brush painting, but Acrylic Color paints can be used with an airbrush when slightly diluted with Acrylic Thinner.

Non-toxic water-based with no latex. Shake well before use. Includes stainless steel mixing ball. Contains 6x 17ml.

Content:

1x Nuclear White
1x Black Stallion
1x Wolven Grey
1x Moonstone Grey
1x Mirage Blue
1x Steel Grey

The perfect combination of paints to create the impression of shining gold on your models, without using any metallic paint! Non-metallic metal set of acrylic paints with an opaque and smooth matt finish, especially designed for modelling and miniature painting. Curated and carefully developed by experienced artists using a new generation of pigments, the Acrylic Color range aims to provide a full spectrum of all basic tones and shades necessary for wargames, vehicles, miniatures and dioramas, as well as colours exclusive to GSW.

Rich in high quality pigments, these colours will leave a fine homogenous layer of fast drying paint, respecting all details on the surface. Perfect for glazes and other techniques, making them adequate for experts and amateurs alike. Designed especially for brush painting, but Acrylic Color paints can be used with an airbrush when slightly diluted with Acrylic Thinner.

Non-toxic water-based with no latex. Shake well before use. Includes stainless steel mixing ball. Contains 6x 17ml.

Content:

1x Banana Split
1x Ochre Desert
1x Leather Brown
1x Choco Brown
1x Dark Umber
1x Ivory Tusk

Textured Rolling Pins capable of pressing a continuous repeated pattern on clay and putties. Made of clear PMMA plastic with amazing non-stick properties. Non-toxic. They come in several different textures that you can purchase based on your specific needs.

Length: 14'50 cm (5’5 inches)
Diameter: 2’5cm (1 inch)

USE INSTRUCTIONS: 

1st - Properly mix the putty/clay until ready according to the manufacturer's recommendations.

2nd - Extend the putty/clay on a surface to be textured. For optimal results, make sure you have got a smooth and even surface before impressing with the Rolling Pins. *** We recommend using a plain Rolling Pin for this.

3rd - Depending on the type of putty/clay, it is advisable to wet the Rolling Pin to prevent any sticking.

4th - Slowly move the Rolling Pin applying equal pressure at all points for an even texture.

5th - Trim any excess putty/clay with a sharp knife. It is recommended to do this once it has dried to avoid any deformations in the putty/clay.

MATERIALS:

There are plenty of different putties and clays on the market and all of them can be textured using the proper technique.

Usually polymer clay (Fimo or Sculpey type) are quite simple to work with these Rolling Pins as they allow for an easy correction of mistakes before they are baked. If the aim is to make textured bases, we recommend using MDF bases, because you can texture the polymer clay directly onto an MDF base, and then put it all in the oven, including the base. The cooking time of these clays are around 15 minutes at 150ºC. MDF Wood may leave a slight scent similar to that of toasted bread, but don't worry it won’t burn!

In the case of epoxy putties, there are a variety of techniques which achieve similar results. Good thing is. you do not need to bake them, so they may be applied directly onto plastic bases.

For Green Stuff putty, which is particularly sticky, it is required to slightly wet either the putty or the Rolling Pin with some water before texturing. You may also reduce the stickiness by applying talcum powder, or using Sculptor Vaseline (LINK).

Other epoxy putties like the Milliput putty, for example, are also suitable, but we wouldn't recommend to wet them much since it will hinder your work. Furthermore, if the mixture is too sticky, it is better to continue kneading until the stickiness is gone.

*** For this type of epoxy putties, it is very important to clean the rolling pins properly after use.

CARE INSTRUCTIONS:

After working with the Rolling Pins, use a Scratch Brush (LINK) and plenty of water to clean off any residue on the Rolling Pins if required.

SAFETY:

To ensure safety, children should be closely monitored by a responsible adult. 

Type: NYLON FLOCK

Fiber Size: 3mm

Content: 180 ml - This format contains an average of 50-80 ml extra over most other brands

Textured Rolling Pins capable of pressing a continuous repeated pattern on clay and putties. Made of clear PMMA plastic with amazing non-stick properties. Non-toxic. They come in several different textures that you can purchase based on your specific needs.

Length: 14'50 cm (5’5 inches)
Diameter: 2’5cm (1 inch)

USE INSTRUCTIONS: 

1st - Properly mix the putty/clay until ready according to the manufacturer's recommendations.

2nd - Extend the putty/clay on a surface to be textured. For optimal results, make sure you have got a smooth and even surface before impressing with the Rolling Pins. *** We recommend using a plain Rolling Pin for this.

3rd - Depending on the type of putty/clay, it is advisable to wet the Rolling Pin to prevent any sticking.

4th - Slowly move the Rolling Pin applying equal pressure at all points for an even texture.

5th - Trim any excess putty/clay with a sharp knife. It is recommended to do this once it has dried to avoid any deformations in the putty/clay.

MATERIALS:

There are plenty of different putties and clays on the market and all of them can be textured using the proper technique.

Usually polymer clay (Fimo or Sculpey type) are quite simple to work with these Rolling Pins as they allow for an easy correction of mistakes before they are baked. If the aim is to make textured bases, we recommend using MDF bases, because you can texture the polymer clay directly onto an MDF base, and then put it all in the oven, including the base. The cooking time of these clays are around 15 minutes at 150ºC. MDF Wood may leave a slight scent similar to that of toasted bread, but don't worry it won’t burn!

In the case of epoxy putties, there are a variety of techniques which achieve similar results. Good thing is. you do not need to bake them, so they may be applied directly onto plastic bases.

For Green Stuff putty, which is particularly sticky, it is required to slightly wet either the putty or the Rolling Pin with some water before texturing. You may also reduce the stickiness by applying talcum powder, or using Sculptor Vaseline (LINK).

Other epoxy putties like the Milliput putty, for example, are also suitable, but we wouldn't recommend to wet them much since it will hinder your work. Furthermore, if the mixture is too sticky, it is better to continue kneading until the stickiness is gone.

*** For this type of epoxy putties, it is very important to clean the rolling pins properly after use.

CARE INSTRUCTIONS:

After working with the Rolling Pins, use a Scratch Brush (LINK) and plenty of water to clean off any residue on the Rolling Pins if required.

SAFETY:

To ensure safety, children should be closely monitored by a responsible adult. 

Martian Fluor Tufts

Decorate your sci-fi and magical themes bases or dioramas with these unique bright fluorescent martian tufts to make them look that they are in a distant galaxy.
Choose the most appropriate color from the extensive Martian Botanics collection based on the extreme neon color combination. These alien bushes, in addition to the intensity of color in the normal state, also react with ultraviolet light.
For placement, just take the grass tufts out of the package using tweezers and fix them with their self-adhesive sticky bases. Although self-adhesive, a dab of glue may be required to apply to some surfaces for a permanent fix.

Fiber Size: 6mm high
Sheet size: 7x14cm
Content: 75 martian tufts

Martian Fluor Tufts

Decorate your sci-fi and magical themes bases or dioramas with these unique bright fluorescent martian tufts to make them look that they are in a distant galaxy.
Choose the most appropriate color from the extensive Martian Botanics collection based on the extreme neon color combination. These alien bushes, in addition to the intensity of color in the normal state, also react with ultraviolet light.
For placement, just take the grass tufts out of the package using tweezers and fix them with their self-adhesive sticky bases. Although self-adhesive, a dab of glue may be required to apply to some surfaces for a permanent fix.

Fiber Size: 6mm high
Sheet size: 7x14cm
Content: 75 martian tufts

Grass TUFTS XL - 12mm Self-adhesive - BURNT

Innovative self-adhesive scenic basing tufts perfect for decorating miniature bases, scenery, field paths, lake, river shores, embankments & slopes as well as the edges of forests and roads, creating flower beds or to brighten meadows. Just take the grass tufts out of the package using tweezers and fix them with its self-adhesive sticky bases. Although self adhesive, a dab of glue may be required to apply to some surfaces for a permanent fix.

Transparent acrylic filters with a metallic finish that allow to modify and metalize the colour they cover. Apply on top of other flat, metallic, or colourshift colours. Mixed together, or applied successively, they create new combinations. Shiny metallic finish. Valid for brush or airbrush.

They work similarly to Chameleon Colourshifts, but they are just one colour and the chameleonic effect is achieved through the combination of the base colour and the metal filter. You can apply them to any flat colour to essentially turn it into a Chameleon Colourshift of your own design.

It is preferable to apply over dark colours to appreciate their effect better, though over black you'll only see the tone of the metal filter. Over other dark colours you can create many combinations, we encourage you to experiment as the possibilities with these are endless!

Contents

1x 17ml Purple Interference

Textured Rolling Pins capable of pressing a continuous repeated pattern on clay and putties. Made of clear PMMA plastic with amazing non-stick properties. Non-toxic. They come in several different textures that you can purchase based on your specific needs.

Length: 14'50 cm (5’5 inches)
Diameter: 2’5cm (1 inch)

USE INSTRUCTIONS: 

1st - Properly mix the putty/clay until ready according to the manufacturer's recommendations.

2nd - Extend the putty/clay on a surface to be textured. For optimal results, make sure you have got a smooth and even surface before impressing with the Rolling Pins. *** We recommend using a plain Rolling Pin for this.

3rd - Depending on the type of putty/clay, it is advisable to wet the Rolling Pin to prevent any sticking.

4th - Slowly move the Rolling Pin applying equal pressure at all points for an even texture.

5th - Trim any excess putty/clay with a sharp knife. It is recommended to do this once it has dried to avoid any deformations in the putty/clay.

MATERIALS:

There are plenty of different putties and clays on the market and all of them can be textured using the proper technique.

Usually polymer clay (Fimo or Sculpey type) are quite simple to work with these Rolling Pins as they allow for an easy correction of mistakes before they are baked. If the aim is to make textured bases, we recommend using MDF bases, because you can texture the polymer clay directly onto an MDF base, and then put it all in the oven, including the base. The cooking time of these clays are around 15 minutes at 150ºC. MDF Wood may leave a slight scent similar to that of toasted bread, but don't worry it won’t burn!

In the case of epoxy putties, there are a variety of techniques which achieve similar results. Good thing is. you do not need to bake them, so they may be applied directly onto plastic bases.

For Green Stuff putty, which is particularly sticky, it is required to slightly wet either the putty or the Rolling Pin with some water before texturing. You may also reduce the stickiness by applying talcum powder, or using Sculptor Vaseline (LINK).

Other epoxy putties like the Milliput putty, for example, are also suitable, but we wouldn't recommend to wet them much since it will hinder your work. Furthermore, if the mixture is too sticky, it is better to continue kneading until the stickiness is gone.

*** For this type of epoxy putties, it is very important to clean the rolling pins properly after use.

CARE INSTRUCTIONS:

After working with the Rolling Pins, use a Scratch Brush (LINK) and plenty of water to clean off any residue on the Rolling Pins if required.

SAFETY:

To ensure safety, children should be closely monitored by a responsible adult. 

Acrylic paints with an opaque and smooth matt finish, especially designed for modelling and miniature painting. Formula curated and carefully developed by experienced artists using a new generation of pigments, the Acrylic Color range aims to provide a full spectrum of all basic tones and shades necessary for wargames, vehicles, miniatures and dioramas, as well as colours exclusive to GSW.

Rich in high quality pigments, these colours will leave a fine homogenous layer of fast drying paint, respecting all details on the surface. Perfect for glazes and other techniques, making them adequate for experts and amateurs alike. Designed especially for brush painting, but Acrylic Color paints can be used with an airbrush when slightly diluted with Acrylic Thinner.

Non-toxic water-based with no latex. Shake well before use. Includes stainless steel mixing ball.

Contains: 17ml.

*This Paint may contain a protective seal, remove before use.

Super Sculpey Beige sculpting compound for modeling detailed finished sculptures. This Polymer clay is used when making miniatures, maquettes, and dolls of any kind, but also is popular model clay used by movie animation studios and professionals worldwide.

As all polymer clays it won’t harden until is baked during 15 minutes at 130ºC (275°F) to a ceramic-like hardness, afterwards it may be carved, sanded to a fine smoothness, drilled and painted. Baking may be done in any regular oven.

Acrylic paints with an opaque and smooth matt finish, especially designed for modelling and miniature painting. Formula curated and carefully developed by experienced artists using a new generation of pigments, the Acrylic Color range aims to provide a full spectrum of all basic tones and shades necessary for wargames, vehicles, miniatures and dioramas, as well as colours exclusive to GSW.

Rich in high quality pigments, these colours will leave a fine homogenous layer of fast drying paint, respecting all details on the surface. Perfect for glazes and other techniques, making them adequate for experts and amateurs alike. Designed especially for brush painting, but Acrylic Color paints can be used with an airbrush when slightly diluted with Acrylic Thinner.

Non-toxic water-based with no latex. Shake well before use. Includes stainless steel mixing ball.

Contains: 17ml.

*This Paint may contain a protective seal, remove before use.

Textured Rolling Pins capable of pressing a continuous repeated pattern on clay and putties. Made of clear PMMA plastic with amazing non-stick properties. Non-toxic. They come in several different textures that you can purchase based on your specific needs.

Length: 14'50 cm (5’5 inches)
Diameter: 2’5cm (1 inch)
Pattern Size: 1-4 mm (variable with multiple stone types, all of them different)
Recommended Scales: 1/144 - 1/100 - 1/72 (12-15-20mm miniatures)

USE INSTRUCTIONS:

1st - Properly mix the putty/clay until ready according to the manufacturer's recommendations.

2nd - Extend the putty/clay on a surface to be textured. For optimal results, make sure you have got a smooth and even surface before impressing with the Rolling Pins. *** We recommend using a plain Rolling Pin for this.

3rd - Depending on the type of putty/clay, it is advisable to wet the Rolling Pin to prevent any sticking.

4th - Slowly move the Rolling Pin applying equal pressure at all points for an even texture.

5th - Trim any excess putty/clay with a sharp knife. It is recommended to do this once it has dried to avoid any deformations in the putty/clay.

MATERIALS:

There are plenty of different putties and clays on the market and all of them can be textured using the proper technique.

Usually polymer clay (Fimo or Sculpey type) are quite simple to work with these Rolling Pins as they allow for an easy correction of mistakes before they are baked. If the aim is to make textured bases, we recommend using MDF bases, because you can texture the polymer clay directly onto an MDF base, and then put it all in the oven, including the base. The cooking time of these clays are around 15 minutes at 150ºC. MDF Wood may leave a slight scent similar to that of toasted bread, but don't worry it won’t burn!

In the case of epoxy putties, there are a variety of techniques which achieve similar results. Good thing is. you do not need to bake them, so they may be applied directly onto plastic bases.

For Green Stuff putty, which is particularly sticky, it is required to slightly wet either the putty or the Rolling Pin with some water before texturing. You may also reduce the stickiness by applying talcum powder, or using Sculptor Vaseline (LINK).

Other epoxy putties like the Milliput putty, for example, are also suitable, but we wouldn't recommend to wet them much since it will hinder your work. Furthermore, if the mixture is too sticky, it is better to continue kneading until the stickiness is gone.

*** For this type of epoxy putties, it is very important to clean the rolling pins properly after use.

CARE INSTRUCTIONS:

After working with the Rolling Pins, use a Scratch Brush and plenty of water to clean off any residue on the Rolling Pins if required.

SAFETY:

To ensure safety, children should be closely monitored by a responsible adult.

Textured Rolling Pins capable of pressing a continuous repeated pattern on clay and putties. Made of clear PMMA plastic with amazing non-stick properties. Non-toxic. They come in several different textures that you can purchase based on your specific needs.

Length: 14'50 cm (5’5 inches)
Diameter: 2’5cm (1 inch)
Pattern Size: 1-4 mm (variable with multiple stone types, all of them different)
Recommended Scales: 1/144 - 1/100 - 1/72 (12-15-20mm miniatures)

USE INSTRUCTIONS:

1st - Properly mix the putty/clay until ready according to the manufacturer's recommendations.

2nd - Extend the putty/clay on a surface to be textured. For optimal results, make sure you have got a smooth and even surface before impressing with the Rolling Pins. *** We recommend using a plain Rolling Pin for this.

3rd - Depending on the type of putty/clay, it is advisable to wet the Rolling Pin to prevent any sticking.

4th - Slowly move the Rolling Pin applying equal pressure at all points for an even texture.

5th - Trim any excess putty/clay with a sharp knife. It is recommended to do this once it has dried to avoid any deformations in the putty/clay.

MATERIALS:

There are plenty of different putties and clays on the market and all of them can be textured using the proper technique.

Usually polymer clay (Fimo or Sculpey type) are quite simple to work with these Rolling Pins as they allow for an easy correction of mistakes before they are baked. If the aim is to make textured bases, we recommend using MDF bases, because you can texture the polymer clay directly onto an MDF base, and then put it all in the oven, including the base. The cooking time of these clays are around 15 minutes at 150ºC. MDF Wood may leave a slight scent similar to that of toasted bread, but don't worry it won’t burn!

In the case of epoxy putties, there are a variety of techniques which achieve similar results. Good thing is. you do not need to bake them, so they may be applied directly onto plastic bases.

For Green Stuff putty, which is particularly sticky, it is required to slightly wet either the putty or the Rolling Pin with some water before texturing. You may also reduce the stickiness by applying talcum powder, or using Sculptor Vaseline (LINK).

Other epoxy putties like the Milliput putty, for example, are also suitable, but we wouldn't recommend to wet them much since it will hinder your work. Furthermore, if the mixture is too sticky, it is better to continue kneading until the stickiness is gone.

*** For this type of epoxy putties, it is very important to clean the rolling pins properly after use.

CARE INSTRUCTIONS:

After working with the Rolling Pins, use a Scratch Brush and plenty of water to clean off any residue on the Rolling Pins if required.

SAFETY:

To ensure safety, children should be closely monitored by a responsible adult.

Set of Silicone Containment Moulds that allow you to limit the edges of the bases of your miniatures when pouring liquids and resins, such as our Ultraviolet Resin. Resin will not stick to the silicone nor will it affect the transparency of the resins.

These moulds have the standard measurements of wargame bases. During the filling with resins, to reduce any potential deformities due to the high temperatures generated, we recommend the application of the resin in thin layers. Do not move or manipulate these moulds with resin inside until they have been completely hardened, since air may have trapped inside, releasing it and generating internal bubbles.

These moulds are heat resistant up to 240ºC and very durable.

Dimensions:

60x35mm
75x42mm
90x52mm
105x70mm
70x25mm

Height: 10mm

Textured Rolling Pins capable of pressing a continuous repeated pattern on clay and putties. Made of clear PMMA plastic with amazing non-stick properties. Non-toxic. They come in several different textures that you can purchase based on your specific needs.

Length: 14'50 cm (5’5 inches)
Diameter: 2’5cm (1 inch)

USE INSTRUCTIONS: 

1st - Properly mix the putty/clay until ready according to the manufacturer's recommendations.

2nd - Extend the putty/clay on a surface to be textured. For optimal results, make sure you have got a smooth and even surface before impressing with the Rolling Pins. *** We recommend using a plain Rolling Pin for this.

3rd - Depending on the type of putty/clay, it is advisable to wet the Rolling Pin to prevent any sticking.

4th - Slowly move the Rolling Pin applying equal pressure at all points for an even texture.

5th - Trim any excess putty/clay with a sharp knife. It is recommended to do this once it has dried to avoid any deformations in the putty/clay.

MATERIALS:

There are plenty of different putties and clays on the market and all of them can be textured using the proper technique.

Usually polymer clay (Fimo or Sculpey type) are quite simple to work with these Rolling Pins as they allow for an easy correction of mistakes before they are baked. If the aim is to make textured bases, we recommend using MDF bases, because you can texture the polymer clay directly onto an MDF base, and then put it all in the oven, including the base. The cooking time of these clays are around 15 minutes at 150ºC. MDF Wood may leave a slight scent similar to that of toasted bread, but don't worry it won’t burn!

In the case of epoxy putties, there are a variety of techniques which achieve similar results. Good thing is. you do not need to bake them, so they may be applied directly onto plastic bases.

For Green Stuff putty, which is particularly sticky, it is required to slightly wet either the putty or the Rolling Pin with some water before texturing. You may also reduce the stickiness by applying talcum powder, or using Sculptor Vaseline (LINK).

Other epoxy putties like the Milliput putty, for example, are also suitable, but we wouldn't recommend to wet them much since it will hinder your work. Furthermore, if the mixture is too sticky, it is better to continue kneading until the stickiness is gone.

*** For this type of epoxy putties, it is very important to clean the rolling pins properly after use.

CARE INSTRUCTIONS:

After working with the Rolling Pins, use a Scratch Brush (LINK) and plenty of water to clean off any residue on the Rolling Pins if required.

SAFETY:

To ensure safety, children should be closely monitored by a responsible adult.