Textured Rolling Pins capable of pressing a continuous repeated pattern on clay and putties. Made of clear PMMA plastic with amazing non-stick properties. Non-toxic. They come in several different textures that you can purchase based on your specific needs.

Length: 14'50 cm (5’5 inches)
Diameter: 2’5cm (1 inch)

USE INSTRUCTIONS: 

1st - Properly mix the putty/clay until ready according to the manufacturer's recommendations.

2nd - Extend the putty/clay on a surface to be textured. For optimal results, make sure you have got a smooth and even surface before impressing with the Rolling Pins. *** We recommend using a plain Rolling Pin for this.

3rd - Depending on the type of putty/clay, it is advisable to wet the Rolling Pin to prevent any sticking.

4th - Slowly move the Rolling Pin applying equal pressure at all points for an even texture.

5th - Trim any excess putty/clay with a sharp knife. It is recommended to do this once it has dried to avoid any deformations in the putty/clay.

MATERIALS:

There are plenty of different putties and clays on the market and all of them can be textured using the proper technique.

Usually polymer clay (Fimo or Sculpey type) are quite simple to work with these Rolling Pins as they allow for an easy correction of mistakes before they are baked. If the aim is to make textured bases, we recommend using MDF bases, because you can texture the polymer clay directly onto an MDF base, and then put it all in the oven, including the base. The cooking time of these clays are around 15 minutes at 150ºC. MDF Wood may leave a slight scent similar to that of toasted bread, but don't worry it won’t burn!

In the case of epoxy putties, there are a variety of techniques which achieve similar results. Good thing is. you do not need to bake them, so they may be applied directly onto plastic bases.

For Green Stuff putty, which is particularly sticky, it is required to slightly wet either the putty or the Rolling Pin with some water before texturing. You may also reduce the stickiness by applying talcum powder, or using Sculptor Vaseline (LINK).

Other epoxy putties like the Milliput putty, for example, are also suitable, but we wouldn't recommend to wet them much since it will hinder your work. Furthermore, if the mixture is too sticky, it is better to continue kneading until the stickiness is gone.

*** For this type of epoxy putties, it is very important to clean the rolling pins properly after use.

CARE INSTRUCTIONS:

After working with the Rolling Pins, use a Scratch Brush (LINK) and plenty of water to clean off any residue on the Rolling Pins if required.

SAFETY:

To ensure safety, children should be closely monitored by a responsible adult. 

Textured Rolling Pins capable of pressing a continuous repeated pattern on clay and putties. Made of clear PMMA plastic with amazing non-stick properties. Non-toxic. They come in several different textures that you can purchase based on your specific needs.

Length: 14'50 cm (5’5 inches)
Diameter: 2’5cm (1 inch)

USE INSTRUCTIONS: 

1st - Properly mix the putty/clay until ready according to the manufacturer's recommendations.

2nd - Extend the putty/clay on a surface to be textured. For optimal results, make sure you have got a smooth and even surface before impressing with the Rolling Pins. *** We recommend using a plain Rolling Pin for this.

3rd - Depending on the type of putty/clay, it is advisable to wet the Rolling Pin to prevent any sticking.

4th - Slowly move the Rolling Pin applying equal pressure at all points for an even texture.

5th - Trim any excess putty/clay with a sharp knife. It is recommended to do this once it has dried to avoid any deformations in the putty/clay.

MATERIALS:

There are plenty of different putties and clays on the market and all of them can be textured using the proper technique.

Usually polymer clay (Fimo or Sculpey type) are quite simple to work with these Rolling Pins as they allow for an easy correction of mistakes before they are baked. If the aim is to make textured bases, we recommend using MDF bases, because you can texture the polymer clay directly onto an MDF base, and then put it all in the oven, including the base. The cooking time of these clays are around 15 minutes at 150ºC. MDF Wood may leave a slight scent similar to that of toasted bread, but don't worry it won’t burn!

In the case of epoxy putties, there are a variety of techniques which achieve similar results. Good thing is. you do not need to bake them, so they may be applied directly onto plastic bases.

For Green Stuff putty, which is particularly sticky, it is required to slightly wet either the putty or the Rolling Pin with some water before texturing. You may also reduce the stickiness by applying talcum powder, or using Sculptor Vaseline (LINK).

Other epoxy putties like the Milliput putty, for example, are also suitable, but we wouldn't recommend to wet them much since it will hinder your work. Furthermore, if the mixture is too sticky, it is better to continue kneading until the stickiness is gone.

*** For this type of epoxy putties, it is very important to clean the rolling pins properly after use.

CARE INSTRUCTIONS:

After working with the Rolling Pins, use a Scratch Brush (LINK) and plenty of water to clean off any residue on the Rolling Pins if required.

SAFETY:

To ensure safety, children should be closely monitored by a responsible adult. 

Textured Rolling Pins capable of pressing a continuous repeated pattern on clay and putties. Made of clear PMMA plastic with amazing non-stick properties. Non-toxic. They come in several different textures that you can purchase based on your specific needs.

Length: 14'50 cm (5’5 inches)
Diameter: 2’5cm (1 inch)

USE INSTRUCTIONS: 

1st - Properly mix the putty/clay until ready according to the manufacturer's recommendations.

2nd - Extend the putty/clay on a surface to be textured. For optimal results, make sure you have got a smooth and even surface before impressing with the Rolling Pins. *** We recommend using a plain Rolling Pin for this.

3rd - Depending on the type of putty/clay, it is advisable to wet the Rolling Pin to prevent any sticking.

4th - Slowly move the Rolling Pin applying equal pressure at all points for an even texture.

5th - Trim any excess putty/clay with a sharp knife. It is recommended to do this once it has dried to avoid any deformations in the putty/clay.

MATERIALS:

There are plenty of different putties and clays on the market and all of them can be textured using the proper technique.

Usually polymer clay (Fimo or Sculpey type) are quite simple to work with these Rolling Pins as they allow for an easy correction of mistakes before they are baked. If the aim is to make textured bases, we recommend using MDF bases, because you can texture the polymer clay directly onto an MDF base, and then put it all in the oven, including the base. The cooking time of these clays are around 15 minutes at 150ºC. MDF Wood may leave a slight scent similar to that of toasted bread, but don't worry it won’t burn!

In the case of epoxy putties, there are a variety of techniques which achieve similar results. Good thing is. you do not need to bake them, so they may be applied directly onto plastic bases.

For Green Stuff putty, which is particularly sticky, it is required to slightly wet either the putty or the Rolling Pin with some water before texturing. You may also reduce the stickiness by applying talcum powder, or using Sculptor Vaseline (LINK).

Other epoxy putties like the Milliput putty, for example, are also suitable, but we wouldn't recommend to wet them much since it will hinder your work. Furthermore, if the mixture is too sticky, it is better to continue kneading until the stickiness is gone.

*** For this type of epoxy putties, it is very important to clean the rolling pins properly after use.

CARE INSTRUCTIONS:

After working with the Rolling Pins, use a Scratch Brush (LINK) and plenty of water to clean off any residue on the Rolling Pins if required.

SAFETY:

To ensure safety, children should be closely monitored by a responsible adult. 

Textured Rolling Pins capable of pressing a continuous repeated pattern on clay and putties. Made of clear PMMA plastic with amazing non-stick properties. Non-toxic. They come in several different textures that you can purchase based on your specific needs.

Length: 14'50 cm (5’5 inches)
Diameter: 2’5cm (1 inch)

USE INSTRUCTIONS: 

1st - Properly mix the putty/clay until ready according to the manufacturer's recommendations.

2nd - Extend the putty/clay on a surface to be textured. For optimal results, make sure you have got a smooth and even surface before impressing with the Rolling Pins. *** We recommend using a plain Rolling Pin for this.

3rd - Depending on the type of putty/clay, it is advisable to wet the Rolling Pin to prevent any sticking.

4th - Slowly move the Rolling Pin applying equal pressure at all points for an even texture.

5th - Trim any excess putty/clay with a sharp knife. It is recommended to do this once it has dried to avoid any deformations in the putty/clay.

MATERIALS:

There are plenty of different putties and clays on the market and all of them can be textured using the proper technique.

Usually polymer clay (Fimo or Sculpey type) are quite simple to work with these Rolling Pins as they allow for an easy correction of mistakes before they are baked. If the aim is to make textured bases, we recommend using MDF bases, because you can texture the polymer clay directly onto an MDF base, and then put it all in the oven, including the base. The cooking time of these clays are around 15 minutes at 150ºC. MDF Wood may leave a slight scent similar to that of toasted bread, but don't worry it won’t burn!

In the case of epoxy putties, there are a variety of techniques which achieve similar results. Good thing is. you do not need to bake them, so they may be applied directly onto plastic bases.

For Green Stuff putty, which is particularly sticky, it is required to slightly wet either the putty or the Rolling Pin with some water before texturing. You may also reduce the stickiness by applying talcum powder, or using Sculptor Vaseline (LINK).

Other epoxy putties like the Milliput putty, for example, are also suitable, but we wouldn't recommend to wet them much since it will hinder your work. Furthermore, if the mixture is too sticky, it is better to continue kneading until the stickiness is gone.

*** For this type of epoxy putties, it is very important to clean the rolling pins properly after use.

CARE INSTRUCTIONS:

After working with the Rolling Pins, use a Scratch Brush (LINK) and plenty of water to clean off any residue on the Rolling Pins if required.

SAFETY:

To ensure safety, children should be closely monitored by a responsible adult. 

Textured Rolling Pins capable of pressing a continuous repeated pattern on clay and putties. Made of clear PMMA plastic with amazing non-stick properties. Non-toxic. They come in several different textures that you can purchase based on your specific needs.

Length: 14'50 cm (5’5 inches)
Diameter: 2’5cm (1 inch)

USE INSTRUCTIONS: 

1st - Properly mix the putty/clay until ready according to the manufacturer's recommendations.

2nd - Extend the putty/clay on a surface to be textured. For optimal results, make sure you have got a smooth and even surface before impressing with the Rolling Pins. *** We recommend using a plain Rolling Pin for this.

3rd - Depending on the type of putty/clay, it is advisable to wet the Rolling Pin to prevent any sticking.

4th - Slowly move the Rolling Pin applying equal pressure at all points for an even texture.

5th - Trim any excess putty/clay with a sharp knife. It is recommended to do this once it has dried to avoid any deformations in the putty/clay.

MATERIALS:

There are plenty of different putties and clays on the market and all of them can be textured using the proper technique.

Usually polymer clay (Fimo or Sculpey type) are quite simple to work with these Rolling Pins as they allow for an easy correction of mistakes before they are baked. If the aim is to make textured bases, we recommend using MDF bases, because you can texture the polymer clay directly onto an MDF base, and then put it all in the oven, including the base. The cooking time of these clays are around 15 minutes at 150ºC. MDF Wood may leave a slight scent similar to that of toasted bread, but don't worry it won’t burn!

In the case of epoxy putties, there are a variety of techniques which achieve similar results. Good thing is. you do not need to bake them, so they may be applied directly onto plastic bases.

For Green Stuff putty, which is particularly sticky, it is required to slightly wet either the putty or the Rolling Pin with some water before texturing. You may also reduce the stickiness by applying talcum powder, or using Sculptor Vaseline (LINK).

Other epoxy putties like the Milliput putty, for example, are also suitable, but we wouldn't recommend to wet them much since it will hinder your work. Furthermore, if the mixture is too sticky, it is better to continue kneading until the stickiness is gone.

*** For this type of epoxy putties, it is very important to clean the rolling pins properly after use.

CARE INSTRUCTIONS:

After working with the Rolling Pins, use a Scratch Brush (LINK) and plenty of water to clean off any residue on the Rolling Pins if required.

SAFETY:

To ensure safety, children should be closely monitored by a responsible adult. 

Textured Rolling Pins capable of pressing a continuous repeated pattern on clay and putties. Made of clear PMMA plastic with amazing non-stick properties. Non-toxic. They come in several different textures that you can purchase based on your specific needs.

Length: 14'50 cm (5’5 inches)
Diameter: 2’5cm (1 inch)

USE INSTRUCTIONS: 

1st - Properly mix the putty/clay until ready according to the manufacturer's recommendations.

2nd - Extend the putty/clay on a surface to be textured. For optimal results, make sure you have got a smooth and even surface before impressing with the Rolling Pins. *** We recommend using a plain Rolling Pin for this.

3rd - Depending on the type of putty/clay, it is advisable to wet the Rolling Pin to prevent any sticking.

4th - Slowly move the Rolling Pin applying equal pressure at all points for an even texture.

5th - Trim any excess putty/clay with a sharp knife. It is recommended to do this once it has dried to avoid any deformations in the putty/clay.

MATERIALS:

There are plenty of different putties and clays on the market and all of them can be textured using the proper technique.

Usually polymer clay (Fimo or Sculpey type) are quite simple to work with these Rolling Pins as they allow for an easy correction of mistakes before they are baked. If the aim is to make textured bases, we recommend using MDF bases, because you can texture the polymer clay directly onto an MDF base, and then put it all in the oven, including the base. The cooking time of these clays are around 15 minutes at 150ºC. MDF Wood may leave a slight scent similar to that of toasted bread, but don't worry it won’t burn!

In the case of epoxy putties, there are a variety of techniques which achieve similar results. Good thing is. you do not need to bake them, so they may be applied directly onto plastic bases.

For Green Stuff putty, which is particularly sticky, it is required to slightly wet either the putty or the Rolling Pin with some water before texturing. You may also reduce the stickiness by applying talcum powder, or using Sculptor Vaseline (LINK).

Other epoxy putties like the Milliput putty, for example, are also suitable, but we wouldn't recommend to wet them much since it will hinder your work. Furthermore, if the mixture is too sticky, it is better to continue kneading until the stickiness is gone.

*** For this type of epoxy putties, it is very important to clean the rolling pins properly after use.

CARE INSTRUCTIONS:

After working with the Rolling Pins, use a Scratch Brush (LINK) and plenty of water to clean off any residue on the Rolling Pins if required.

SAFETY:

To ensure safety, children should be closely monitored by a responsible adult. 

Spare Paint Pots for mixes with mixing Steel Balls 

Set of spare empty paint bottles in 17mL with mixing steel balls and dropper.

Agitator balls will garantee a proper mixture of all paint contents and therefore they will avoid having all pigments deposited in the bottom of the pot specially after long term storage.

These mixing balls are coming with a special coat to make them completely paint proof which will avoid rusting after long periods in contact with paints that may ruin your paints. They are not magnetic but they will be attracted by magnets.

Content: 

5x empty paint pots 17ml
5x Droppers
5x Mixing stell balls in 6.35mm

MDF BASES - ROUND 40mm 

Top quality MDF bases for mounting wargames figures.

This single component high viscosity no-drip gel cyanoacrylate adhesive is ideal for bonding porous materials or when controlling adhesive flow is critical. Offers maximum gap-filling and repositioning time. Drying time 5-10 seconds.

CONTENT:1x 20gr. CA modeling glue gel

RECOMMENDATIONS:

- Use Glue tips available at our site to extend the lifetime of the bottles
- If you are not planning to use the CA glue for a long period of time prepare the glue for storage: remove the glue tip, clean and wipe your CA bottle nozzle and neck, and re-cap it.
- Make sure your CA glue is stored away from your CA Glue Activator. The accelerator gives off fumes (aerosols) just sitting there, which can cause CA glue to harden in the bottle prematurely. We recommend a zip-lock bag for the accelerator.

MDF BASES - ROUND 32mm 

Top quality MDF bases for mounting wargames figures.

MDF BASES - ROUND 25mm

Top quality MDF bases for mounting wargames figures.

Instant modeling glue from Green Stuff World, commonly known as cyanoacrylate glue, is the best super glue for plastic, and it is also a type of Cyanoacrylate that is widely used in various applications such as woodworking, model making, and jewelry making. This high-performance product is designed to bond a wide range of materials in 5-10 seconds including Plasticard, foams, rubber, metal, cork, wood, and ceramics. It is quick-drying properties and strong bond make it a popular choice for DIY projects and professional applications alike.

This is a single-component adhesive that is based on a family of synthetic acrylic resins known as cyanoacrylates. When applied to a surface, the adhesive quickly reacts with the moisture in the air to form a strong bond. The ciano is supplied in a bottle and is dispensed through a nozzle applicator.

When using it, it's important to take safety precautions to avoid skin or eye contact. The ciano is also known to release fumes during the curing process, so proper ventilation is recommended.

CONTENT: 1x Instant Glue 20gr.

Kneadatite Brown Stuff it is a room-temperature curing two-part epoxy/polyamide putty. Excellent adhesion to metal, and 90 minutes of worklife. 

Brown Stuff is similar to Green Stuff but sets slightly harder and remains malleable. Bown Stuff has a thicker consistency so it is a little easier to work with for beginners. Brown Stuff can be mixed with other putties to vary the carving and working texture and also the final hardness.

Cures very hard, great for finer details such as sharp tips, points, weapon blades, armours, and other hard-line details.

Both strips of material in the package are not in contact, to avoid waste of material.

This set contains 12 inches of material --> 30 cm

Kneadatite Brown Stuff it is a room-temperature curing two-part epoxy/polyamide putty. Excellent adhesion to metal, and 90 minutes of worklife. 

Brown Stuff is similar to Green Stuff but sets slightly harder and remains malleable. Bown Stuff has a thicker consistency so it is a little easier to work with for beginners. Brown Stuff can be mixed with other putties to vary the carving and working texture and also the final hardness.

Cures very hard, great for finer details such as sharp tips, points, weapon blades, armours, and other hard-line details.

Both strips of material in the package are not in contact to avoid waste of material.

This set contains 18 inches of material --> 46 cm

Kneadatite Brown Stuff it is a room-temperature curing two-part epoxy/polyamide putty. Excellent adhesion to metal, and 90 minutes of worklife. 

Brown Stuff is similar to Green Stuff but sets slightly harder and remains malleable. Bown Stuff has a thicker consistency so it is a little easier to work with for beginners. Brown Stuff can be mixed with other putties to vary the carving and working texture and also the final hardness.

Cures very hard, great for finer details such as sharp tips, points, weapon blades, armours, and other hard-line details.

Both strips of material in the package are not in contact, to avoid waste of material.

This set contains 6 inches of material --> 15 cm