Milliput is a epoxy putty used by modellers for all kind of applications. Each package contains two separate bars, one of which is a hardener. Upon mixing an equal quantity of each different bar the material starts to harden, and hardens fully in 90 minutes, after which it can be carved, sanded, drilled, and sculpted over.

If you are interrupted while you are mixing Milliput, you can put the Milliput into a deep freezer until you can get back to work. This will keep the product at approximately the same state of setting at which it was frozen for up to 24 hours

OTHER ADVANTANGES:

-        In combination with water will allow to get extra smooth surfaces.

-        It allows you easily to merge new layers of milliput over

-        It will not get stuck to your either your fingers or your tools

-        Once dried, it can be carved, sanded and drilled

-        Once dried, it remains very hard and resistance. You may mix it with Plasticine or other clays to save putty reducing it hardness.

-        Heat resistance up to 130ºC.

Kneadatite Blue/Yellow Green Stuff is a room-temperature curing two-part epoxy putty sold either in tape format. 

Mixing equal parts of the yellow 'filler' and blue 'hardener' produces a sticky green putty that feels a lot like chewed bubble gum. Once mixed, it has a worklife of 90 minutes, allowing time for shaping and detailing, reaching 'ultimate hardness' after 24 hours. Altering the mix with more blue or yellow component will produce a faster/slower and harder/softer cure.

We recommend to use a little lubricant to prevent Green Stuff from sticking. Normally water is enough but some people also use others such as Vaseline, petroleum jelly or even jhonson baby oil to get smooth surfaces. Keep wet fingers and tools to make easier the sculpting and modeling process. You may also add talcum powder to reduce the stickiness and avoid fingerprints.

This set contains 12 inches of material --> 30 cm.

Extra fine-grained, water-based and fast-drying putty with an extra hard finish. Specially designed for modeling and perfect as a superfine filler due to its adhesion and sanding properties. Does not shrink when drying. Can be cleaned and thinned with water. Non toxic and non flammable.

Contains: 20ml

Kneadatite Blue/Yellow Green Stuff is a room-temperature curing two-part epoxy putty sold either in tape format. 

Mixing equal parts of the yellow 'filler' and blue 'hardener' produces a sticky green putty that feels a lot like chewed bubble gum. Once mixed, it has a worklife of 90 minutes, allowing time for shaping and detailing, reaching 'ultimate hardness' after 24 hours. Altering the mix with more blue or yellow component will produce a faster/slower and harder/softer cure.

We recommend to use a little lubricant to prevent Green Stuff from sticking. Normally water is enough but some people also use others such as Vaseline, petroleum jelly or even jhonson baby oil to get smooth surfaces. Keep wet fingers and tools to make easier the sculpting and modeling process. You may also add talcum powder to reduce the stickiness and avoid fingerprints.

This Set contains 18 inches of material --> 46 cm

Milliput White is similar to Milliput Standard but much more suitable to get finer and smaller detailed pieces in all kind of applications. Each package contains two separate bars, one of which is a hardener. Upon mixing an equal quantity of each different bar the material starts to harden, and hardens fully in 90 minutes, after which it can be carved, sanded, drilled, and sculpted over.

If you are interrupted while you are mixing Milliput, you can put the Milliput into a deep freezer until you can get back to work. This will keep the product at approximately the same state of setting at which it was frozen for up to 24 hours

OTHER ADVANTANGES:

-        In combination with water will allow to get extra smooth surfaces.

-        It allows you easily to merge new layers of milliput over

-        It will not get stuck to your either your fingers or your tools

-        Once dried, it can be carved, sanded and drilled

-        Once dried, it remains very hard and resistance. You may mix it with Plasticine or other clays to save putty reducing it hardness.

-        Heat resistance up to 130ºC

Kneadatite Blue/Yellow Green Stuff is a room-temperature curing two-part epoxy putty sold in tape format. 

Mixing equal parts of the yellow 'filler' and blue 'hardener' produces a sticky green putty that feels a lot like chewed bubble gum. Once mixed, it has a worklife of 90 minutes, allowing time for shaping and detailing, reaching 'ultimate hardness' after 24 hours. Altering the mix with more blue or yellow component will produce a faster/slower and harder/softer cure.

We recommend to use a little lubricant to prevent Green Stuff from sticking. Normally water is enough but some people also use others such as Vaseline to get smooth surfaces. Keep wet fingers and tools to make easier the sculpting and modelling process. You may also add talcum powder to reduce the stickiness and avoid fingerprints.

This set contains 36'5 inches of material --> 93 cm

Kneadatite Brown Stuff it is a room-temperature curing two-part epoxy/polyamide putty. Excellent adhesion to metal, and 90 minutes of worklife. 

Brown Stuff is similar to Green Stuff but sets slightly harder and remains malleable. Bown Stuff has a thicker consistency so it is a little easier to work with for beginners. Brown Stuff can be mixed with other putties to vary the carving and working texture and also the final hardness.

Cures very hard, great for finer details such as sharp tips, points, weapon blades, armours, and other hard-line details.

Both strips of material in the package are not in contact, to avoid waste of material.

This set contains 6 inches of material --> 15 cm

Kneadatite Brown Stuff it is a room-temperature curing two-part epoxy/polyamide putty. Excellent adhesion to metal, and 90 minutes of worklife. 

Brown Stuff is similar to Green Stuff but sets slightly harder and remains malleable. Bown Stuff has a thicker consistency so it is a little easier to work with for beginners. Brown Stuff can be mixed with other putties to vary the carving and working texture and also the final hardness.

Cures very hard, great for finer details such as sharp tips, points, weapon blades, armours, and other hard-line details.

Both strips of material in the package are not in contact to avoid waste of material.

This set contains 18 inches of material --> 46 cm

Kneadatite Brown Stuff it is a room-temperature curing two-part epoxy/polyamide putty. Excellent adhesion to metal, and 90 minutes of worklife. 

Brown Stuff is similar to Green Stuff but sets slightly harder and remains malleable. Bown Stuff has a thicker consistency so it is a little easier to work with for beginners. Brown Stuff can be mixed with other putties to vary the carving and working texture and also the final hardness.

Cures very hard, great for finer details such as sharp tips, points, weapon blades, armours, and other hard-line details.

Both strips of material in the package are not in contact, to avoid waste of material.

This set contains 12 inches of material --> 30 cm

Kneadatite Blue/Yellow Green Stuff is a room-temperature curing two-part epoxy putty sold either in bar format. 

Mixing equal parts of the yellow 'filler' and blue 'hardener' produces a sticky green putty that feels a lot like chewed bubble gum. Once mixed, it has a worklife of 90 minutes, allowing time for shaping and detailing, reaching 'ultimate hardness' after 24 hours. Altering the mix with more blue or yellow component will produce a faster/slower and harder/softer cure.

We recommend to use a little lubricant to prevent Green Stuff from sticking. Normally water is enough but some people also use others such as Vaseline, petroleum jelly or even jhonson baby oil to get smooth surfaces. Keep wet fingers and tools to make easier the sculpting and modeling process.

You may also add talcum powder to reduce the stickiness and avoid fingerprints.

This Set includes 100 gr. of material in Bar format.

Milliput is a epoxy putty used by modellers for all kind of applications. Each package contains two separate bars, one of which is a hardener. Upon mixing an equal quantity of each different bar the material starts to harden, and hardens fully in 90 minutes, after which it can be carved, sanded, drilled, and sculpted over.

If you are interrupted while you are mixing Milliput, you can put the Milliput into a deep freezer until you can get back to work. This will keep the product at approximately the same state of setting at which it was frozen for up to 24 hours

OTHER ADVANTANGES:

-        In combination with water will allow to get extra smooth surfaces.

-        It allows you easily to merge new layers of milliput over

-        It will not get stuck to your either your fingers or your tools

-        Once dried, it can be carved, sanded and drilled

-        Once dried, it remains very hard and resistance. You may mix it with Plasticine or other clays to save putty reducing it hardness.

-        Heat resistance up to 130ºC.

Milliput is a epoxy putty used by modellers for all kind of applications. Each package contains two separate bars, one of which is a hardener. Upon mixing an equal quantity of each different bar the material starts to harden, and hardens fully in 90 minutes, after which it can be carved, sanded, drilled, and sculpted over.

If you are interrupted while you are mixing Milliput, you can put the Milliput into a deep freezer until you can get back to work. This will keep the product at approximately the same state of setting at which it was frozen for up to 24 hours

OTHER ADVANTANGES:

-        In combination with water will allow to get extra smooth surfaces.

-        It allows you easily to merge new layers of milliput over

-        It will not get stuck to your either your fingers or your tools

-        Once dried, it can be carved, sanded and drilled

-        Once dried, it remains very hard and resistance. You may mix it with Plasticine or other clays to save putty reducing it hardness.

-        Heat resistance up to 130ºC.

Kneadatite Brown Stuff it is a room-temperature curing two-part epoxy/polyamide putty. Excellent adhesion to metal, and 90 minutes of worklife. 

Brown Stuff is similar to Green Stuff but sets slightly harder and remains malleable. Bown Stuff has a thicker consistency so it is a little easier to work with for beginners. Brown Stuff can be mixed with other putties to vary the carving and working texture and also the final hardness.

Cures very hard, great for finer details such as sharp tips, points, weapon blades, armours, and other hard-line details.

Both strips of material in the package are not in contact, to avoid waste of material.

This set contains 36'5 inches of material --> 93 cm

Milliput is a epoxy putty used by modellers for all kind of applications. Each package contains two separate bars, one of which is a hardener. Upon mixing an equal quantity of each different bar the material starts to harden, and hardens fully in 90 minutes, after which it can be carved, sanded, drilled, and sculpted over.

If you are interrupted while you are mixing Milliput, you can put the Milliput into a deep freezer until you can get back to work. This will keep the product at approximately the same state of setting at which it was frozen for up to 24 hours

OTHER ADVANTANGES:

-        In combination with water will allow to get extra smooth surfaces.

-        It allows you easily to merge new layers of milliput over

-        It will not get stuck to your either your fingers or your tools

-        Once dried, it can be carved, sanded and drilled

-        Once dried, it remains very hard and resistance. You may mix it with Plasticine or other clays to save putty reducing it hardness.

-        Heat resistance up to 130ºC.

Milliput is a epoxy putty used by modellers for all kind of applications. Each package contains two separate bars, one of which is a hardener. Upon mixing an equal quantity of each different bar the material starts to harden, and hardens fully in 90 minutes, after which it can be carved, sanded, drilled, and sculpted over.

If you are interrupted while you are mixing Milliput, you can put the Milliput into a deep freezer until you can get back to work. This will keep the product at approximately the same state of setting at which it was frozen for up to 24 hours

OTHER ADVANTANGES:

-        In combination with water will allow to get extra smooth surfaces.

-        It allows you easily to merge new layers of milliput over

-        It will not get stuck to your either your fingers or your tools

-        Once dried, it can be carved, sanded and drilled

-        Once dried, it remains very hard and resistance. You may mix it with Plasticine or other clays to save putty reducing it hardness.

-        Heat resistance up to 130ºC.

Super Sculpey Beige sculpting compound for modeling detailed finished sculptures. This Polymer clay is used when making miniatures, maquettes, and dolls of any kind, but also is popular model clay used by movie animation studios and professionals worldwide.

As all polymer clays it won’t harden until is baked during 15 minutes at 130ºC (275°F) to a ceramic-like hardness, afterwards it may be carved, sanded to a fine smoothness, drilled and painted. Baking may be done in any regular oven.

Super Sculpey Medium Blend 454 gr.

The best blend of both Super Sculpey and Super Sculpey Firm. The new hybrid clay is closer to sculpey Firm in terms of hardness, has many amazing attributes:
- Thinner baked areas hold up to pressure – sand thin limbs without anything cracking or snapping.
- Firm enough to hold it’s shape, yet soft/ malleable enough to comfortably build/shape and blend pieces together. Enables the consumer to carve detail into their piece easily.
- This clay permits you to use build up methods that are more additive and focused on building out shapes in small increments. Once the clay has been kneaded slightly, it is highly malleable and ready to blend. Cuts down on sanding time because it blends so smoothly. Has elasticity yet is firm enough to enable great detail.
- Shatter and chip resistant.

100% sulfur free.

Super Sculpey Beige (55 gr.) sculpting compound for modeling detailed finished sculptures. This Polymer clay is used when making miniatures, maquettes, and dolls of any kind, but also is popular model clay used by movie animation studios and professionals worldwide.

As all polymer clays it won’t harden until is baked during 15 minutes at 130ºC (275°F) to a ceramic-like hardness, afterwards it may be carved, sanded to a fine smoothness, drilled and painted. Baking may be done in any regular oven.

Super Sculpey Beige (55 gr.) sculpting compound for modeling detailed finished sculptures. This Polymer clay is used when making miniatures, maquettes, and dolls of any kind, but also is popular model clay used by movie animation studios and professionals worldwide.

As all polymer clays it won’t harden until is baked during 15 minutes at 130ºC (275°F) to a ceramic-like hardness, afterwards it may be carved, sanded to a fine smoothness, drilled and painted. Baking may be done in any regular oven.

Bakeable adhesive Sculpey Bake & Bond, that forms an incredibly strong bond between two pieces of clay.
It eliminates the need to apply excessive pressure to join clay pieces and prevents the distortion of shapes and fine details
May also be used to adhere clay to porous materials such as paper, wood or canvas.

Content: 59ml

Milliput is a epoxy putty used by modellers for all kind of applications. Each package contains two separate bars, one of which is a hardener. Upon mixing an equal quantity of each different bar the material starts to harden, and hardens fully in 90 minutes, after which it can be carved, sanded, drilled, and sculpted over.

If you are interrupted while you are mixing Milliput, you can put the Milliput into a deep freezer until you can get back to work. This will keep the product at approximately the same state of setting at which it was frozen for up to 24 hours

OTHER ADVANTANGES:

-        In combination with water will allow to get extra smooth surfaces.

-        It allows you easily to merge new layers of milliput over

-        It will not get stuck to your either your fingers or your tools

-        Once dried, it can be carved, sanded and drilled

-        Once dried, it remains very hard and resistance. You may mix it with Plasticine or other clays to save putty reducing it hardness.

-        Heat resistance up to 130ºC.