Blue Stuff sticks is a new generation of thermo plastic molding material wich can be reduced to mouldable conditions by inmmersion in hot water during 3 minutes.
It will allow you to create an instant mold of any piece you wanted by pressing the plastic material against the piece you want to have the mold made from. After that, make copies by using any kind of putty, polyester resins or even epoxy resins. Nothing will get stuck. REUSABLE plastic moulding for all levels.
New improved formulation that will allow you to have better details since the plastic will remain more time in soft state.
This set contains 4 bars and it will last for ever.
Dimension of each bar: 5.8x1.5x0.7cm Weight of each bar: 6 gr
Blue Stuff sticks is a new generation of thermo plastic molding material wich can be reduced to mouldable conditions by inmmersion in hot water during 3 minutes.
It will allow you to create an instant mold of any piece you wanted by pressing the plastic material against the piece you want to have the mold made from. After that, make copies by using any kind of putty, polyester resins or even epoxy resins. Nothing will get stuck. REUSABLE plastic moulding for all levels.
New improved formulation that will allow you to have better details since the plastic will remain more time in soft state.
This set contains 4 bars and it will last for ever.
Dimension of each bar: 5.8x1.5x0.7cm Weight of each bar: 6 gr
Roll Makeris the ultimate tool to make all kind of tubes, tentacles, and wires to be used with any kind of putty or clay.
Depending on your sculpting material you may need to wet repeatedly the plates or your fingers with bit of water to reduce stickiness. Adding talcum powder to water may help with some putties like Green Stuff.
Use a toothbrush to clear any residue from plates if required, and never use wire brushes or metal implements since plates may be damages.
This set includes:
2 large plates 2 medium plates 2 small plates 2 guide bars. Use them to hold the plates and to get an extra 45º position for new textures.
Set of round stainless steel cutters in the most frequent diamensions used to create bases as well as fillings of bases. That will allow you to cut clays and other materials quickly.
Roll Makeris the ultimate tool to make all kind of tubes, tentacles, and wires to be used with any kind of putty or clay.
Depending on your sculpting material you may need to wet repeatedly the plates or your fingers with bit of water to reduce stickiness. Adding talcum powder to water may help with some putties like Green Stuff.
Use a toothbrush to clear any residue from plates if required, and never use wire brushes or metal implements since plates may be damages.
Roll Maker XL will allow to make tentacles up to 75mm length without joints, and it also combinable with Roll Maker standard versión, since all plates are different in size. Guide bars are now stackable to allow you to make thicker pieces such us columns or trees.
This set includes: 2 large plates - XL Version 2 curved plates - XL Version 2 small plates - XL Version 2 STACKABLE guide bars. Use them to hold the plates and to get an extra 45º position for new textures.
An assortment of different types of RPG dice moulds make of flexible clear silicone. It can be used with many materials such as UV resin, epoxy resin, polyester resin, polyurethane resin, wax, soap, polymer clays, and more. Why not make party dice from chocolate or ice? Heat resistant to 200ºC.
They come with 2 parts, the main dice and a lid with a number a hole to release air bubbles.
Set of Silicone Containment Moulds that allow you to limit the edges of the bases of your miniatures when pouring liquids and resins, such as our Ultraviolet Resin. Resin will not stick to the silicone nor will it affect the transparency of the resins.
These moulds have the standard measurements of wargame bases. During the filling with resins, to reduce any potential deformities due to the high temperatures generated, we recommend the application of the resin in thin layers. Do not move or manipulate these moulds with resin inside until they have been completely hardened, since air may have trapped inside, releasing it and generating internal bubbles.
These moulds are heat resistant up to 240ºC and very durable.:
The Sculptor Vaseline fromGreen Stuff Worldis the result of mixing several refined petroleum jellies, oils, waxes, beeswax and other mineral components that give it a distinctive blue color. It has been specially designed formodelingand sculpting.
It is odorless and semisolid in its normal state.
USES:
- As lubricant forsculpting toolsor ourtextured rolling pins. - To smooth the finish of sculptures. - As bonding agent for polymer clays. - As conditioner for crumbled clays and putties. - To soften the natural texture of putties. - To achieve thinner layers with clays and putties. - To improve blending of clays and putties.
It should be stored at room temperature. If exposed to high temperatures, it could soften. To recover its original solidity, place it for a few minutes in the refrigerator.
Set of ovalstainless steelcutters in the most frequent dimensions used to create bases as well as fillings of bases. That will allow you to cut clays and other materials quickly. Perfect forAge of Sigmarbases.
"Made of high quality foodgrade silicone, easy to use and intricately cut for great impressions, these molds are heat resistant and durable. The molds are extra deep to give highly detailed beautiful results for both dimensional design and surface imprinting. Each mold has a large surface area, measuring approximately 2,5x5 inches (6x12cm), and is unmounted for optimal usability. The molds work great with food and any sort of resin.
Heat resistant silicone up to 240ºC
Resin-Grade
We recommend using SCRAPERS to remove the excess of putty from the molds without cutting them.
Thickness of the molds: 4mm
Thickness of the pieces produced with these molds: 3mm
Set of Silicone Containment Moulds that allow you to limit the edges of the bases of your miniatures when pouring liquids and resins, such as our Ultraviolet Resin. Resin will not stick to the silicone nor will it affect the transparency of the resins.
These moulds have the standard measurements of wargame bases. During the filling with resins, to reduce any potential deformities due to the high temperatures generated, we recommend the application of the resin in thin layers. Do not move or manipulate these moulds with resin inside until they have been completely hardened, since air may have trapped inside, releasing it and generating internal bubbles.
These moulds are heat resistant up to 240ºC and very durable.
"Made of high quality foodgrade silicone, easy to use and intricately cut for great impressions, these molds are heat resistant and durable. The molds are extra deep to give highly detailed beautiful results for both dimensional design and surface imprinting. Each mold has a large surface area, measuring approximately 2,5x5 inches (6x12cm), and is unmounted for optimal usability. The molds work great with food and any sort of resin.
Heat resistant silicone up to 240ºC
Resin-Grade
We recommend using SCRAPERS to remove the excess of putty from the molds without cutting them.
Thickness of the molds: 4mm
Thickness of the pieces produced with these molds: 3mm
"Made of high quality foodgrade silicone, easy to use and intricately cut for great impressions, these molds are heat resistant and durable. The molds are extra deep to give highly detailed beautiful results for both dimensional design and surface imprinting. Each mold has a large surface area, measuring approximately 2,5x5 inches (6x12cm), and is unmounted for optimal usability. The molds work great with food and any sort of resin.
Heat resistant silicone up to 240ºC
Resin-Grade
We recommend using SCRAPERS to remove the excess of putty from the molds without cutting them.
Thickness of the molds: 4mm
Thickness of the pieces produced with these molds: 3mm"
Made of high quality foodgrade silicone, easy to use and intricately cut for great impressions, these molds are heat resistant (up to 240ºC) and durable. The molds are carefully carved for highly detailed and thorough results for both dimensional design and surface imprinting. Each mold has a large surface area measuring 6x12cm.
The molds work great with any sort of resin, we highly recommend usingacrylic resin. Wait until the resin has dried completely before removing the pieces. Other materials such as milliput, milliput mixed with plasteline, magic sculpt and others also work but are harder to use. We recommend the use ofscrapers to remove excess putty/clay from the molds without damaging them.
Set of ovalstainless steelcutters in the most frequent dimensions used to create bases as well as fillings of bases. That will allow you to cut clays and other materials quickly. Perfect forAge of Sigmarbases.
Made of high quality foodgrade silicone, easy to use and intricately cut for great impressions, these molds are heat resistant and durable. The molds are extra deep to give highly detailed beautiful results for both dimensional design and surface imprinting. Each mold has a large surface area, measuring approximately 2,5x5 inches (6x12cm), and is unmounted for optimal usability. The molds work great with food and any sort of resin.
Heat resistant silicone up to 240ºC
Resin-Grade
We recommend using SCRAPERS to remove the excess of putty from the molds without cutting them.
Thickness of the molds: 4mm
Thickness of the pieces produced with these molds: 3mm
"Made of high quality foodgrade silicone, easy to use and intricately cut for great impressions, these molds are heat resistant and durable. The molds are extra deep to give highly detailed beautiful results for both dimensional design and surface imprinting. Each mold has a large surface area, measuring approximately 2,5x5 inches (6x12cm), and is unmounted for optimal usability. The molds work great with food and any sort of resin.
Heat resistant silicone up to 240ºC
Resin-Grade
We recommend using SCRAPERS to remove the excess of putty from the molds without cutting them.
Thickness of the molds: 4mm
Thickness of the pieces produced with these molds: 3mm
This mold can make:
6 Tyres of 12.5 x 4.2mm
2 Hubcapped wheels of 12.5 x 4.2mm
6 Tyres of 18 x 5mm
2 Hubcapped wheels of 18x5mm."
Set of Silicone Containment Moulds that allow you to limit the edges of the bases of your miniatures when pouring liquids and resins, such as our Ultraviolet Resin. Resin will not stick to the silicone nor will it affect the transparency of the resins.
These moulds have the standard measurements of wargame bases. During the filling with resins, to reduce any potential deformities due to the high temperatures generated, we recommend the application of the resin in thin layers. Do not move or manipulate these moulds with resin inside until they have been completely hardened, since air may have trapped inside, releasing it and generating internal bubbles.
These moulds are heat resistant up to 240ºC and very durable.:
